Hydrogen is stored as a compressed gas at 35 to 100 MPa, and five types of pressure vessel compete for the job. Each trades weight, cost and long-term behavior differently, and the right choice depends on whether the vessel sits at a fueling station, rides on a truck or goes into a vehicle. Here is how they compare, and what each one demands from the designer.
| Type | Construction | Main hydrogen concern | Typical use |
|---|---|---|---|
| 1 | All metal, usually steel | Embrittlement and fatigue crack growth | Stationary storage |
| 2 | Metal liner, hoop-wrapped composite | Crack growth in the steel liner | Station storage up to 100 MPa |
| 3 | Aluminum liner, fully wrapped | Liner fatigue life | Vehicles, trailers, smaller storage |
| 4 | Polymer liner, fully wrapped | Permeation, boss sealing, liner collapse | 70 MPa vehicles, large tube trailers |
| 5 | No liner, all composite | Permeation through the laminate | Aerospace, development |
Type 1 and Type 2: steel, and the fight against crack growth
Type 1 vessels are all metal, usually high-strength steel. Type 2 vessels add a hoop wrap of carbon or glass fiber over a steel liner. Both are heavy, so they suit stationary storage, and both are relatively low cost. Their weakness is the steel itself: high-strength steels exposed to high-pressure hydrogen grow fatigue cracks faster than they would in air.
In the United States these vessels are typically designed to ASME Section VIII, Division 3. Its Article KD-10, which covers high-pressure gaseous hydrogen service, applies to seamless vessels above 41 MPa and allows pressures up to 100 MPa. It requires fatigue crack growth and crack threshold data measured in high-pressure hydrogen gas, and uses fracture mechanics to set the vessel's design life. Material selection, heat treatment and an almost flawless internal surface finish all matter.
Type 3: an aluminum liner, fully wrapped
Type 3 vessels use a seamless aluminum liner fully wrapped in carbon fiber composite. The liner keeps the gas in, so permeation is not a concern, and aluminum alloys of the kind used for these liners are considered compatible with hydrogen. The design challenge moves to the liner's fatigue life at very high pressure. That depends heavily on the composite: the winding sequence, fiber tension, cure cycle and autofrettage pressure all have to be calculated and controlled. Liner forming also limits how large a Type 3 vessel can be made.
Type 4: a polymer liner, the lightest practical option
Type 4 vessels use a polymer liner fully wrapped in composite. They offer the best combination of weight and cost, and they can be built much larger than Type 3, which is why large tube trailers and 70 MPa vehicle tanks use them. Three issues dominate the design:
- Permeation. Hydrogen molecules are small and pass slowly through polymers. HDPE liners are common at lower pressures; at higher pressures designers often move to lower-permeation polyamides such as PA6, or to multilayer liners.
- The polar boss seal. The joint between the plastic liner and the metal boss must stay leak-tight for 20 years or more. In our experience a combination of adhesive bonding and mechanical compression seals works best.
- Liner collapse. A liner saturated with hydrogen can blister or buckle when the vessel is depressurized quickly. Our article on what investigators look at first covers how this shows up in a failure.
For stationary hydrogen storage, ASME Section X added an appendix in its 2010 edition for composite vessels with non-load-sharing liners up to 15,000 psi (about 103 MPa), and ISO 19884 covers cylinders and tubes for stationary storage up to 110 MPa. Vehicle tanks follow their own standards, such as ANSI/CSA HGV 2, UN GTR No. 13 and ISO 19881.
Type 5: no liner at all
Type 5 vessels drop the liner and rely on the composite laminate alone. They are the lightest option and have a long history in aerospace, but for hydrogen the laminate itself must stop permeation over the vessel's whole life, which remains a demanding problem.
Where the cost is
Whatever the type, the composite drives the cost of a hydrogen vessel. In a typical wet-wound Type 4 cost breakdown that Shaun Hogan presented at the Composites Excellence Center of Asia in 2025, carbon fiber alone was about 70 percent of factory cost, and carbon fiber with resin more than 80 percent. Real savings come from using the fiber efficiently: low-void laminates with straight, unwrinkled fibers, fiber strength design values taken from burst testing rather than handbook data, and winding processes that hold those properties in production.
Choosing a vessel type
Start from the duty, not the technology: stationary or mobile, the number of pressure cycles, the space and weight limits, the gas quality and the approval route. A fueling station buffer that cycles many times a day, a tube trailer that must carry as much gas as possible, and a vehicle tank that must survive a crash call for different answers, often from different standards.
This is a general technical overview. Each design must be qualified to the standard and approval route that applies to it.
Sources
- San Marchi, Somerday and Nibur: fatigue crack growth of SA-372 steel in 100 MPa hydrogen following Article KD-10 (Sandia, 2013)
- H2Tools: ASME BPVC Section X, fiber-reinforced plastic pressure vessels
- NRC Canada: ISO 19884, gaseous hydrogen cylinders and tubes for stationary storage
- NHTSA DOT HS 811 832: life cycle testing of 70 MPa hydrogen containers